SPINNING MILL SHORT FORMULA EXPLANATION

 SPINNING MILL SHORT FORMULAS :-

    In spinning mill we use production formula in short method. I recommend to use  formula in elaborate. First we need some basic details is given below

GENERAL:-

1 METER = 1.094 YARD

1 LEA = 120 YARD

7 LEA = 840 YARD

1 KG = 2.20456 POUNDS

1 CM = 10 MM

1 INCH = 2.54 CM

1 INCH = 25.4 MM


Mostly Spinning people use short formula like

0.2835×Delivery speed in mpm÷ Hank for MPM to Kgs

And 1693×1.890(weight in kg)×count for Find autoconer cone length.

Where its comes?

First we take short formula 0.2835

Here we use 0.2835 and MPM and Hank. What was the actual formula

MPM*1.094*8*60/840/2.20456/HANK*EFF/100*No. of delivery

so we omit the MPM And hank in this formula

1.094*8*60/840/2.20456 = 0.2835.


Second we take short formula 1693

We use formula the above same

Length*1.094*8*60/840/2.20456/count = Weight

But here we need the Length. So reverse the formula

840*2.20456*1.094 =1692.71 = 1693.


ELABORATE FORMULA

 In basically we use two formula mostly. one is where we have METER PER MIN (MPM) and another one is where we have REVOLUTION PER MIN(RPM)

MPM FORMULA:-

PRODUCTION FORMULA 8HRS = MPM×1.094×8×60÷840÷2.20456÷HANK*EFF÷100×No. of delivery

RPM FORMULA:-

PRODUCTION FORMULA 8HRS=  RPM×8×60÷36÷840÷2.20456÷COUNT÷TPI*EFF÷100×No. of delivery

COMBER NPM PRODUCTION FORMULA 8HRS:-

FORMULA = NPM×8×60×NO. OF HEADS×FEED PER NIP× GMS ÷PER METER×(100-NOIL)÷1000×1000×100×EFF÷100

COMBER FEED PER NIP FORMULA :-

FORMULA = 3.14×BOTTOM ROLLER DIA÷RATCHET WHEEL TEETH


Comments

Post a Comment

If you have any doubts, Pls let me know

Popular posts from this blog

RKM

RKM INFORMATION This can be expressed by the “Length of yarn in km” at which yarn will break of its own weight”. This is equivalent to breaking load in g/tex. RKM is the short expression for “Reisskilometer” – “Breaking-kilometre”, which is an unit out of date. E.g.: a Cotton-yarn with 15 RKM means, it would break of its own weight, if you wind off 15 km of the yarn and hang it up in 15 km. Nowadays it is common practice, to use the unit Centi-Newton per Tex (cN/Tex) or gram-force per Tex (gf/Tex). RKM and cN/Tex or gf/Tex are practically the same (a slight difference would be there)   SINGLE YARN STRENGTH (Breaking force) :  This is the force required to break a strand of single yarn. It is expressing Centi-Newton (cN).     STRENGTH (Tenacity) : The Tensile Strength expressed as force per unit linear density is called Tenacity. This is normally expressed as gram force per tex (gf/tex).   CSP (Count Strength Product) : CSP, the bundle strength...
Read more

LOW RKM REASONS

LOW RKM REASONS BLENDING OF MIXING TO BE ENSURED AND IF NECESSARY TUMBLING TO  BE DONE. TO START WITH SLIGHTLY RICHER MIXING AND BACK TO USUAL MIXING% GRADUALLY. AVOID BYPASSING OF THE BEATERS. CHANGING OF THE CARD LINES TO BE AVOIDED . TO START WITH HIGHER NOIL% AND REDUCE GRADUALLY TO USUAL    IF REQUIRED. SOFT WASTE ADDING TO BE AVOIDED FOR FIRST 3 OR 4 MIXINGS. IN SIMPLEX M/C CHECK THE FOLLOWING     a)FALSE TWISTER CONDITION     b)FLOATING CONDENSER CONDITION.     C)DAMAGE COT/APRON.     d)DEFECTIVE SADDLES.     f)TOP ARM LOAD.     g)PRESSER EYE CONDITION.     h)FLUFF ACCUMULATION ON FLYER HOLE.     i)BOBBIN CLEARANCE VARIATION.     j)CONE DRUM NOISE     k)FEED CAN CONDITION         l)SLIVER SPITING. IN SPINNING M/C CHECK THE FOLLOWING:     a)CRISIS-CROSS ROVING.     b)BOBBIN HOLDER ROTATION.     C)DAMAGE COT/APRON. ...
Read more

HOW TO REDUCE CLASSIMATE FAULTS

REDUCING CLASSIMATE FAULTS 1) Count wise online Classmate classes wise results to be record on daily basis 2) Before allotting this work we want to educate quality investigator about Classmate faults and also class wise reasons we want to explain. While noting time investigator has highlight which class is having continuous higher side and same one communicate to that concern dept with reasons 3) We want to fix which classes we want to reduce 4) On daily basis monitoring we can get idea in which zone we r having problem and which zone we want to improve the work methods and process  5) Based on trend analysis we want to inspect process auditing and find out practical problems and also Training awareness we want to give to operators for reducing some classes  6) We can take process trials based on Online Classmate results  7) Regularly we want to compare daily Online results Vs Trial sample results for knowing Where we are Note: Choosing of quality investigator is import...
Read more

Subscribe for Free Articles

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

* indicates required

Intuit Mailchimp