Skip to main content

REASON FOR LONG AND THIN FAULTS

By

REASON FOR LONG AND THIN FAULTS

1. Excessive incidence of web falling, partial or full in cards. This is due to cotton used with higher mic value, or poor Rh%, or higher web tension draft.

2. Too high a creel draft, or break draft, or web tension draft in drawing.


3. Excessive variation in top roller pressure in drawing.


4. Worn out top roller end bushes, or worn out shells in draw frame.


5. Disturbance for the free rotation of creel calendar roller.


6. Sliver stretch on the creel ,of the simplex due high creel tension draft, or creel roller drive struck up.


7. Too high a break draft in simplex.


8. Excessive roving stretch, due to improper function of builder motion mechanism.


9. Use of empty roving bobbin in simplex, with wide variation in bare bobbin diameter.


10. Sliver splitting in simplex, while drafting, or sliver splitting on the creel.


11. Sliver not running, in the center of the top arm.


12. Creel stretch of roving in ring frame due to obstruction in free rotation of the bobbin holder.


13.  Roving stretched in the roving condenser, due to waste chocking in the roving condenser.


14. Due to lower tape tension, lower tpi inserted in the yarn, it causes stretch at further process.


15. Excessive speed of coiler in draw frame.


16. Larger diameter trumpet selection in drawing, also causes creel stretch in simplex.


17. Life ended false twister will insert lower tpi, comparing to good condition false twister, resulting in roving stretch in further process.

Labels:

Comments

Post a Comment

If you have any doubts, Pls let me know

Popular posts from this blog

RKM

By
RKM INFORMATION This can be expressed by the “Length of yarn in km” at which yarn will break of its own weight”. This is equivalent to breaking load in g/tex. RKM is the short expression for “Reisskilometer” – “Breaking-kilometre”, which is an unit out of date. E.g.: a Cotton-yarn with 15 RKM means, it would break of its own weight, if you wind off 15 km of the yarn and hang it up in 15 km. Nowadays it is common practice, to use the unit Centi-Newton per Tex (cN/Tex) or gram-force per Tex (gf/Tex). RKM and cN/Tex or gf/Tex are practically the same (a slight difference would be there)   SINGLE YARN STRENGTH (Breaking force) :  This is the force required to break a strand of single yarn. It is expressing Centi-Newton (cN).     STRENGTH (Tenacity) : The Tensile Strength expressed as force per unit linear density is called Tenacity. This is normally expressed as gram force per tex (gf/tex).   CSP (Count Strength Product) : CSP, the bundle strength...
Post a Comment
Read more

LOW RKM REASONS

By
LOW RKM REASONS TO START WITH SLIGHTLY RICHER MIXING AND BACK TO USUAL MIXING% GRADUALLY. AVOID BYPASSING OF THE BEATERS. CHANGING OF THE CARD LINES TO BE AVOIDED . TO START WITH HIGHER NOIL% AND REDUCE GRADUALLY TO USUAL    IF REQUIRED. SOFT WASTE ADDING TO BE AVOIDED FOR FIRST 3 OR 4 MIXINGS. IN SIMPLEX M/C CHECK THE FOLLOWING     a) FALSE TWISTER CONDITION     b) FLOATING CONDENSER CONDITION .     C) DAMAGE COT/APRON .     d) DEFECTIVE SADDLES .     f) TOP ARM LOAD .     g) PRESSER EYE CONDITION .     h) FLUFF ACCUMULATION ON FLYER HOLE .     i) BOBBIN CLEARANCE VARIATION .     j) CONE DRUM NOISE     k) FEED CAN CONDITION         l) SLIVER SPITING . IN SPINNING M/C CHECK THE FOLLOWING:     a) CRISIS-CROSS ROVING .     b) BOBBIN HOLDER ROTATION .     C)DAMAGE COT/APRON.     d)DEFECTIVE SADDLES.     f)TOP ...
Post a Comment
Read more

HOW TO REDUCE CLASSIMATE FAULTS

By
REDUCING CLASSIMATE FAULTS 1) Count wise online Classmate classes wise results to be record on daily basis 2) Before allotting this work we want to educate quality investigator about Classmate faults and also class wise reasons we want to explain. While noting time investigator has highlight which class is having continuous higher side and same one communicate to that concern dept with reasons 3) We want to fix which classes we want to reduce 4) On daily basis monitoring we can get idea in which zone we r having problem and which zone we want to improve the work methods and process  5) Based on trend analysis we want to inspect process auditing and find out practical problems and also Training awareness we want to give to operators for reducing some classes  6) We can take process trials based on Online Classmate results  7) Regularly we want to compare daily Online results Vs Trial sample results for knowing Where we are Note: Choosing of quality investigator is import...
Post a Comment
Read more